Leaking, Corroded, or Burst Pipes in Howard, CO? Masters Plumbing Service Fixes It
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Howard, CO use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
Acoustic & Thermal Leak LocationAll Pipe MaterialsPress-Fit & Sweat CapableLicensed in CO
Our Capabilities
How Masters Plumbing Service Approaches Pipe Repair in Howard
The biggest cost variable in pipe repair isn't parts — it's how much structure gets opened to find and access the failure. Precise pre-repair location tools reduce that cost significantly.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
Pipe Repair Solutions for Howard Homes
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
Galvanized steel pipe was standard in homes built before the 1960s. It corrodes from the inside out — zinc coating depletes, iron oxide (rust) accumulates on the inner wall, progressively narrowing flow and leaching into the water supply. Repairs on severely corroded galvanized are generally temporary; the pipe is failing systemically along its full run.
PEX
PEX Pipe Repair & Extension
PEX is also the material of choice for extending or reconfiguring supply runs during remodel work. Its flexibility reduces fitting count and eliminates the need for torch work inside walls.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
A burst pipe from freezing or sudden pressure surge requires immediate water shutoff and precise repair. We locate the failure, determine whether it's a single failure point or multiple freeze-damaged sections, and repair with a method appropriate to the pipe material — press-fit coupling for copper, expansion coupling for PEX-A, or a mechanical repair coupling for emergency situations.
Slab Leaks
Under-Slab Pipe Leak Repair
Slab leak rerouting is often more cost-effective than direct access, particularly for longer runs or under tiled floors. We present the options honestly with pricing so you can choose based on your priorities.
Full Repipe
Whole-House Repipe Service
A full repipe in Howard typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
You receive a flat-rate quote covering the specific repair based on what the detection confirmed. We open only what needs to be opened — typically a 12–18 inch drywall or flooring access, not a full wall section.
4
Repair & Pressure Test — Then You're Done
Repair executes immediately on approval. After the repair, we repressurize and hold a pressure test to confirm the failure is fully resolved — not partially. The access opening is left clean for your drywall patch or left ready for your contractor.
Customer Reviews
What Howard Customers Say About Our Pipe Work
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Howard
★★★★★
Had an under-slab leak diagnosed by Masters Plumbing Service with acoustic equipment. They found the leak at 6 feet from the wall — a single copper elbow that had developed a pinhole. Presented three options: direct slab access, reroute through the wall framing above, or copper lining. I chose the reroute — they ran a new PEX line through the crawl space and connected at both ends without touching the slab. Pressure tested, verified no remaining drop. No jackhammering at all.
— O. & R. Adeyemi, Howard, CO
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Howard, CO
Common Questions
Pipe Repair Questions We Answer Every Day
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
Galvanized pipe corrodes from the interior outward — by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1–3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
We don't rush pressure testing at the end. That's the step that confirms the repair is actually complete, and it takes the time it takes.
For slab access openings, we clean up concrete debris, complete the pipe repair, and patch the concrete. Tile or flooring restoration over a slab patch is normally a separate trade.
Service Area
Your Local Pipe Repair Specialists in Howard, CO
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Howard homes and businesses.
Pipe Leaking in Howard, CO? Don't Let It Run — Call Masters Plumbing Service
Active pipe leaks compound fast — mold growth can begin in 24–48 hours of sustained moisture. Masters Plumbing Service's pipe repair crew is in Howard today, equipped with acoustic and thermal detection tools to find the failure precisely before anything is opened.
